Beijer-electronics Industrial Inverter E2 Bedienungsanleitung

10 3.6. Mechanical Dimensions – IP66 (Nema 4X) Enclosed Units Drive Size A / Height B D E F / Depth G / Width H I J Weight mm mm mm mm mm mm mm mm m

11 3.8. Gland Plate and Lock Off The use of a suitable gland system is required to maintain the appropriate IP / Nema rating. Cable entry holes are

12 4. Power Wiring 4.1. Grounding the Drive This manual is intended as a guide for proper installation. The manufacturer cannot assume responsibili

13 4.3. Incoming Power Connection  For 1 phase supply, power should be connected to L1/L, L2/N.  For 3 phase supplies, power should be connecte

14 4.6. Motor Thermal overload Protection. 4.6.1. Internal Thermal Overload Protection. The drive has an in-built motor thermal overload function; t

15 4.9. IP20 & IP66 (Nema 4X) Non- Switched UnitsDrive & Motor Connections For 1 phase supply power should be connected to L1/L, L2/N. For 3

16 4.11. Control Terminal Connections Default Connections Control Terminal Signal Description 1 +24V User Output, +24V, 100mA. 2 Digital Input 1 P

17 5. Operation 5.1. Managing the Keypad The drive is configured and its operation monitored via the keypad and display. NAVIGATE Used to display r

18 5.3. Keypad Control To allow the drive to be controlled from the keypad in a forward direction only, set P-12 =1: 1. Connect Motor as for termi

19 6. Parameters 6.1. Standard Parameters Par. Description Minimum Maximum Default Units P-01 Maximum Frequency / Speed Limit P-02 500.0 50.0 (60.0

2 AC Supply Voltage (50 / 60Hz) L1 L2 L3 Earth

20 6.2. Extended Parameters Par. Description Minimum Maximum Default Units P-15 Digital Input Function Select 0 12 0 - Defines the function of the di

21 Par. Description Minimum Maximum Default Units P-30 Terminal Mode Restart function N/A N/A Auto-0 - Defines the behaviour of the drive relating to

22 Par. Description Minimum Maximum Default Units P-44 PI Reference (Setpoint) Source Select 0 1 0 - Selects the source for the PID Reference / Setpo

23 6.4. P-00 Read Only Status Parameters Description Display range Explanation 1st Analog input value 0 … 100% 100% = max input voltage 

24 7. Analog and Digital Input Configurations 7.1. Terminal Mode (P-12 = 0) P-15 Digital input 1 (T2) Digital input 2 (T3) Digital input 3 (T4) Anal

25 Terminal Mode P-12=0, P-15=3 Terminal Mode P-12=0, P-15=4 Terminal Mode P-12=0, P-15=11 +24 Volt +24 Volt +24 Volt Run (Enable) Run (Enable) Ru

26 7.4. User PI Control Mode P-15 Digital input 1 (T2) Digital input 2 (T3) Digital input 3 (T4) Analog input (T6) Comments 0, 2, 9..12 Open: Stop (d

27 8. Modbus RTU Communications 8.1. Introduction The drive can be connected to a Modbus RTU network via the RJ45 connector on the front of the drive

28 9. Technical Data 9.1. Environmental Operational ambient temperature range Open Drives: -10 … 50°C (frost and condensation free) E

29 9.3. Additional Information for UL Compliance BFI-E2 is designed to meet the UL requirements. In order to ensure full compliance, the following m

3 Motor Cable Sizes - Check the rating information on page 28 - For EMC compliance, u

30 10. Trouble Shooting 10.1. Fault Code Messages Drive Display Fault Code Fault Number Description Corrective Action 0x00 Drive is healthy an

31 Notes:

32  82-E2MAN-BE_V3.20

4 Mechanical Mounting - Information can be found on page 10 Keypad operation can be fo

5 Declaration of Conformity The Manufacturer hereby states that the drive product range conforms to the relevant safety provisions of the Low Voltage

6 1. Introduction ...

7 1. Introduction 1.1. Important Safety Information Please read the IMPORTANT SAFETY INFORMATION below, and all Warning and Caution information else

8 2. General Information and Ratings This chapter contains information about the drive and includes how to identify the drive 2.1. Identifying the

9 3. Mechanical Installation 3.1. General  The drive should be mounted in a vertical position only on a flat, flame resistant vibration free mount